]> Cisco Systems

Greenside, 400 Avenue de Roumanille Sophia Antipolis 06410 France +33 4 97 23 26 19 flefauch@cisco.com

Telecom Italia

Via Reiss Romoli 274 Torino 10148 Italy roberta.maglione@telecomitalia.it

Huawei Technologies

Ottawa Canada tom.taylor.stds@gmail.com

Internet ANCP This document specifies the extensions to the Access Node Control Protocol required for support of the multicast use cases defined in the Access Node Control Protocol framework document and one additional use case described in this document. These use cases are organized into the following ANCP capabilities: NAS-initiated multicast replication; conditional access with white and black lists; conditional access with grey lists; bandwidth delegation; committed bandwidth reporting. These capabilities may be combined according to the rules given in this specification.

defines a framework and requirements for an Access Node control mechanism between a Network Access Server (NAS) and an Access Node (e.g. a Digital Subscriber Line Access Multiplexer (DSLAM)) in a multi-service reference architecture in order to perform QoS-related, service-related and subscriber-related operations. specifies a protocol for Access Node Control in broadband networks in line with this framework. supports three use cases defined in , specifically for DSL access: the DSL Topology Discovery use case, the DSL Line Configuration use case and the DSL Remote Connectivity Test use case. However, it does not support the multicast use cases defined in . The present document specifies the extensions to the Access Node Control Protocol required for support of these multicast use cases. In addition, it supports the Committed Bandwidth Reporting use case, described below. In terms of the ANCP protocol, these use cases are organized into five capabilities: NAS-initiated multicast replication; conditional access with white and black lists; conditional access with grey lists; bandwidth delegation; committed bandwidth reporting. NAS-initiated multicast replication assumes that multicast "join" and "leave" requests are terminated on the NAS, or that the NAS receives requests to establish multicast sessions through other means (e.g., application-level signalling). The NAS sends commands to the AN to start or stop replication of specific multicast flows on specific subscriber ports. This use case is described briefly in the next-to-last paragraph of Section 3.4 of . Conditional access is described in Sections 3.4.1 and 3.4.2.3 of , with the latter section particularly applicable to operation with white and black lists only. In case of "conditional access with white and black lists", multicast join and leave requests are terminated at the AN and accepted or ignored in accordance with the direction provided by white and black lists respectively. The white and black lists are provisioned per port at startup time and may be modified thereafter. The NAS may enable admission control of white-listed flows by appropriate provisioning. Conditional access with grey lists is similar to conditional access with white lists, except that before accepting any request matching a grey list entry, the AN sends a request to the NAS for permission to replicate the flow. Again, the NAS can enable admission control of grey-listed flows at the AN. Bandwidth delegation is described in Section 3.4.2.1 of . It allows flexible sharing of total video bandwidth on an access line between the AN and the NAS. One application of such bandwidth sharing is where the AN does multicast admission control, while the NAS or Policy Server does unicast admission control. In that case, bandwidth delegation allows dynamic sharing of bandwidth between unicast and multicast video traffic on each access line. Committed bandwidth reporting is described below, in . The AN reports the amount of multicast bandwidth it has granted to a given access line each time that value changes. These reports may be buffered for a NAS-provisionable interval so that reports for multiple access lines can be bundled into the same message. The formal specification of the behaviours associated with each of these capabilities, singly and in combination, is given in . In addition to the multicast service processing behaviour just sketched, the definition of each capability includes support for the multicast accounting and reporting services described in Section 3.4.3 of . Because of this common content and because of other protocol overlaps between the different capabilities, the protocol descriptions for the multicast extensions specified in this document are merged into a single non-redundant narrative. Tables in then indicate the specific sub-sections of the protocol description that have to be implemented to support each capability.

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in . The expression "delegated bandwidth" is used as a shorter way of saying: "the total amount of video bandwidth delegated to the AN for multicast admission control".

Quoting from : "... the Access Node, aggregation node(s) and the NAS must all be involved in the multicast replication process. This avoids that several copies of the same stream are sent within the access/aggregation network. In case of an Ethernet-based access/aggregation network, this may, for example, be achieved by means of IGMP snooping or IGMP proxy in the Access Node and aggregation node(s). By introducing IGMP processing in the access/aggregation nodes, the multicast replication process is now divided between the NAS, the aggregation node(s) and Access Nodes. In order to ensure backward compatibility with the ATM-based model, the NAS, aggregation node and Access Node need to behave as a single logical device. This logical device must have exactly the same functionality as the NAS in the ATM access/aggregation network. The Access Node Control Mechanism can be used to make sure that this logical/functional equivalence is achieved by exchanging the necessary information between the Access Node and the NAS." describes the use cases for ANCP associated with such multicast operations, and identifies the associated ANCP requirements. The present section describes a subset of these use cases as background to facilitate reading of this document, but the reader is refered to for a more exhaustive description of the ANCP multicast use cases. Detailed example message flows can also be found in .

One option for multicast handling is for the subscriber to communicate the "join/leave" information to the NAS. This can be done for instance by terminating all subscriber IGMP () or MLD (, ) signaling on the NAS. Another example could be a subscriber using some form of application level signaling, which is redirected to the NAS. In any case, this option is transparent to the access and aggregation network. In this scenario, the NAS uses ANCP to create and remove replication state in the AN for efficient multicast replication. Thus, the NAS only sends a single copy of the multicast stream towards the AN, which in turn performs replication to multiple subscribers as instructed by the NAS via ANCP. The NAS first performs conditional access and multicast admission control when processing multicast join requests, and only creates replication state in the AN if admission succeeds.

With the NAS-initiated use case, a Multicast Replication Control Message is sent by the NAS to the AN with a directive to either join or leave one (or more) multicast flow(s). In the example message flow, the AN uses a Generic Response message to convey the outcome of the directive. illustrates such an ANCP message exchange as well as the associated AN behavior.

| NAS | +----------+ |Gateway| +-----+ +-----+ | +-------+ | | | | | (*) | | | Multicast-Replication-Crl | | | | (Target,add, Flow 1) | | | |<--------------------------| | Mcast Flow 1 | | |<==========================+ | | | | Generic Response | | | |-------------------------->| | | | | | | | | ~ ~ ~ ~ | | | | | | | Multicast-Replication-Crl | | | | (Target,delete, Flow 1) | | | |<--------------------------| | | | | | | Generic Response | | | |-------------------------->| (*) The NAS may optionally seek direction from an external Authorization/Policy Server before admitting the flow.]]>

One option for multicast handling is for the access/aggregation nodes to participate in IGMP/MLD processing (e.g. via IGMP/MLD snooping). In this scenario, on detecting a join/leave request from an end user for a multicast flow (in the grey list), the AN uses ANCP to request a conditional access and admission control decision from the NAS. In turn, after conditional access and admission control checks, the NAS uses ANCP to instruct the AN to change the replication states accordingly.

For support of the conditional access and admission control use case, on detection of an IGMP/MLD Join, the AN sends an Admission Control message to the NAS to request a conditional access and admission control check. In the case of a positive outcome, the NAS sends a Multicast Replication Control Message to the AN with a directive to replicate the multicast flow to the corresponding user. Similarly on detection of an IGMP/MLD leave, an Admission Control message is sent by the AN to the NAS to keep the NAS aware of user departure for the flow. This message flow is illustrated in .

| NAS | +----------+ |Gateway| +-----+ +-----+ | +-------+ | | | | | | | Join(Gr-Flow1) | Admission-Control | |------------+---------->| (Target,add,Gr-Flow1) | | | |-------------------------->| | | | (*) | | | Multicast-Replication-Crl | | | | (Target,add,Gr-Flow1) | | | |<--------------------------| | Mcast Gr-Flow1 | | |<=======================+ | | | | | ~ ~ ~ ~ | | | | | Leave(Gr-Flow1) | Admission-Control | |------------+---------->| (Target,delete,Gr-Flow1) | | | |-------------------------->| | | | | | | | Gr-Flow1: a multicast flow matching the grey list for that port (*) The NAS may optionally seek direction from an external Authorization/Policy Server before admitting the flow.]]>

The Multicast flow reporting use case allows the NAS to asynchronously query the AN to obtain an instantaneous status report related to multicast flows currently replicated by the AN.

The NAS sends a Multicast Flow Query Request message to the AN in order to query the AN about information such as which multicast flows are currently active on a given AN port or which ports are currently replicating a given multicast flow. The AN conveys the requested information to the NAS in a Multicast Flow Query Response message. This message flow is illustrated in .

| NAS | +----------+ |Gateway| +-----+ +-----+ | +-------+ | | | | | Multicast Flow | | | | Query Request | | | |<------------------| | | | | | | | Multicast Flow | | | | Query Response | | | |------------------>| | | | | | | | | ]]>

The committed bandwidth reporting use case allows the NAS to maintain current awareness of how much multicast bandwidth the AN has committed to a given access line, so that the NAS can adjust its forwarding scheduler to ensure the associated QoS. Note that this involves a finer level of detail than provided by bandwidth delegation, since the amount of delegated bandwidth is an upper limit on the amount of bandwidth committed rather than an actual value. To reduce the volume of messaging, reports from the AN may be buffered so that one message reports on changes for multiple access lines.

The message flow associated with this use case is shown in . The figure assumes that a non-zero buffering interval was previously provisioned on the AN.

+-----+ +-------+ +-----+ ANCP +-----+ |Subs |+ | Home |+ | AN |<---------->| NAS | |1,2 || |GW 1,2 || +-----+ +-----+ +-----+| +-------+| | | +|----+ +|------+ | | | | | | | | | |Join(Subs1, Ch1) | | |----------+--------------->| Start buffering | | | | Multicast flow | timer. Create | |<==========================| message with | | | | | | initial contents | | | | | | reporting new | | | | | | Subs1 bandwidth. | | | Join(Subs2, Ch2) | | | |----------+------------->| Add report for | | | | Multicast flow | new Subs2 b/w. | | |<========================| | | | | | | | | |Leave(Subs1, Ch1) | | |----------+--------------->| Replace report | | | | | | for Subs1 with | | | Stop replication X new value (which | | | | | | happens to be | | | | | | the same as the | | | | | | starting value. | | | | | | | | | | | >|< TIMER expires | | | | | | | | | | | |Committed | | | | | | Bandwidth Report | | | | | |------------------>| | | | | | (for latest | | | | | | Subs1 and Subs2 | | | | | | bandwidth) | | | | | | |

This section defines new ANCP messages and new usage of existing ANCP messages as well as procedures associated with the use of these messages.

Section 4.1 of defines the Provisioning message that is sent by the NAS to the AN to provision information in the AN. The present document specifies that the Provisioning message MAY be used by the NAS to provision multicast-related information (e.g., multicast service profiles). The ANCP Provisioning message payload MAY contain: one or more instances of the Multicast-Service-Profile TLV. The Multicast-Service-Profile TLV is defined in the present document in . Each instance of the Multicast-Service-Profile TLV contains a multicast service profile name and one or more list actions. A list action consists of an action (add, delete, replace), a list type (white, black, or grey), and list content (multicast source and group addresses). an instance of the White-List-CAC TLV. The White-List-CAC TLV is defined in . If present, this TLV indicates that the AN is required to do admission control before replicating white-listed flows. an instance of the MRepCtl-CAC TLV. The MRepCtl-CAC TLV is defined in . If present, this TLV indicates that the AN is required to do admission control before replicating flows specified in Multicast Replication Control messages. an instance of the Report-Buffering-Time TLV. The Report-Buffering-Time TLV is defined in . If present, this TLV indicates Committed Bandwidth Report messages should be buffered for the amount of time given by the TLV before being transmitted to the NAS. See for information on which multicast capabilities require support of these TLVs in the Provisioning message.

When directed by the Policy Server or by management action, the NAS sends the Provisioning message to initially provision or to update the white, black, and/or grey multicast channel lists associated with a set of named multicast service profiles, or to enable the AN to perform admission control for specific classes of flows. To provision or update a multicast service profile, the NAS MUST include within the message one or more instances of the Multicast-Service-Profile TLV specifying the content to be provisioned or updated. The NAS SHOULD NOT include any list type (white, black, or grey) that is not supported by the set of multicast capabilities negotiated between the NAS and the AN. The NAS MUST NOT use the Provisioning message to send instances of the Multicast-Service-Profile TLV to the AN unless the Multicast-Service-Profile TLV is supported by the set of multicast capabilities negotiated between the NAS and the AN. To require admission control to be performed at the AN on white-listed flows, the NAS MUST include a copy of the White-List-CAC TLV in the Provisioning message. The White-List-CAC TLV MUST NOT be provided unless the negotiated set of capabilities includes conditional access with white and black lists. To require admission control to be performed at the AN on grey-listed flows or on NAS-initiated flows, the NAS MUST include a copy of the MRepCtl-CAC TLV in the Provisioning message. The MRepCtl-CAC TLV MUST NOT be provided unless the negotiated set of capabilities includes NAS-initiated replication control or conditional access with grey lists. To require buffering of Committed Bandwidth Report messages so that reports for multiple access lines can be included in the same message, the NAS MUST include a copy of the Report-Buffering-Time TLV containing a non-zero time value in a Provisioning message sent to the AN. The Report-Buffering-Time TLV MUST NOT be provided unless the negotiated set of capabilities includes committed bandwidth reporting.

The receiving AN provisions/updates the white, black, and/or grey lists associated with the multicast service profile names contained in the Multicast-Service-Profile TLV instances within the message according to the contents of the associated List-Action TLVs. The AN MUST process List-Action TLVs in the order in which they appear within the message. The AN MUST ignore instances of the List-Action TLV referring to any list type (white, black, or grey) that is not supported by the set of multicast capabilities negotiated between the NAS and the AN. When a new multicast service profile is identified by a Multicast-Service-Profile TLV, the initial state of all lists associated with that profile according to the negotiated set of multicast capabilities is empty until changed by the contents of Multicast-Service-Profile TLVs. The receipt of a Provisioning message containing updates to an existing multicast service profile subsequent to startup will cause the AN to review the status of active flows on all ports to which that profile has been assigned. For further details, see . If the White-List-CAC and/or MRepCtl-CAC TLV is present in the Provisioning message and the respective associated capabilities have been negotiated, the AN prepares (or continues) to do connection admission control on the indicated class(es) of flow. If one or both of these TLVs was present in an earlier Provisioning message but is absent in the latest message received, the AN ceases to do connection admission control on the indicated class(es) of flow. The buffering time specified in an instance of the Report-Buffering-Time TLV applies to only to Committed Bandwidth Report messages initiated after the new buffering time is received at the AN, not to any message already in the process of accumulation. As indicated in , the AN MUST NOT reply to the Provisioning message if it processed it successfully. If an error prevents successful processing of the message content, the AN MUST return a Generic Response message as defined in , containing a Status-Info TLV with the appropriate content describing the error. For this purpose, the presence of a list type in a Multicast-Service-Profile TLV which was ignored because it was not supported by the negotiated set of capabilities is not considered to be an error.

As specified in , the NAS may send DSL line configuration information to the AN ("ANCP based DSL Line Configuration" use case) using ANCP Port Management messages. See Section 7.3 of for the format of the Port Management message in that usage. This document specifies that the Port Management message MAY be used to convey either or both of the following TLVs: Multicast-Service-Profile-Name TLV (defined in ). This TLV associates a Multicast Service Profile with the Access Port specified by the extension block. Bandwidth-Allocation TLV (defined in ). This TLV specifies the total multicast bandwidth available to the AN for admission control at the Access Port. When the Port Management message is used for this purpose: the Function field in the Port Management message MUST be set to 8, "Configure Connection Service Data". the message MUST include TLV(s) to identify the access line concerned. If the access line is a DSL loop, the line-identifying TLV(s) MUST be as specified in Section 5.1.2 of . For non-DSL access lines, the appropriate alternative line-identifying TLV(s) MUST be present. Line configuration data other than the two TLVs listed in the previous paragraph MAY be present.

The NAS sends the Port Management message at startup time to initialize parameters associated with the Access Port specified in the message and with the multicast capabilities negotiated between the NAS and the AN. The NAS MAY send additional Port Management messages subsequent to startup, to update or, in the case of the Bandwidth-Allocation TLV, reset these parameters. If the NAS includes a Multicast-Service-Profile-Name TLV in the Port Management message, the name MUST match a profile name provided in a Multicast-Service-Profile TLV in a prior Provisioning message. The NAS MUST NOT include a TLV unless it is supported by the set of multicast capabilities negotiated between the NAS and the AN. See for further information.

If the Port Management message contains a Multicast-Service-Profile-Name TLV, the AN associates the named profile with the specified Access Port. This association replaces any previous association. That is, a given Access Port is associated with at most one multicast service profile. The replacement of one multicast service profile with another will cause the AN to review the status of all active flows on the target port. For further details see . If the Port Management message contains a Bandwidth-Allocation TLV, the AN adopts this as the current value of its total multicast bandwidth limit for the target port. If the AN has already committed multicast bandwidth exceeding the amount given in the Bandwidth-Allocation TLV, the AN SHOULD NOT discontinue any multicast streams in order to bring bandwidth down to within the new limit. However, the AN MUST NOT admit new multicast streams that are subject to admission control until it can do so within the limit specified by the Bandwidth-Allocation TLV. If the Port Management request cannot be processed due to error and the Result field of the request is Nack (0x1) or AckAll (0x2), the AN SHOULD add a Status-Info TLV to the Extension Value field in its reply if this will provide useful information beyond what is provided by the Result Code value returned in the response header. In particular, if the name within the Multicast-Service-Profile-Name TLV does not match a profile name given in a prior Provisioning message, the AN SHOULD return a reply where the Result Code field in the header indicates 0x55, "Invalid TLV contents", the Error Message field in the Status-Info TLV contains the text "Multicast profile name not provisioned", and the Status-Info TLV contains a copy of the Multicast-Service-Profile-Name TLV.

This section defines a new message called the Multicast Replication Control message. The Multicast Replication Control message is sent by the NAS to the AN with one or more directives to add (join) or delete (leave) a multicast flow on a target object identified in the content of the message. The Message Type for the Multicast Replication Control message is 144. The ANCP Multicast Replication Control message payload contains the following TLVs: Target TLV: The Target TLV is defined in Section 4.3 of . It MUST appear once and only once. It is encoded as specified in or extensions and identifies the AN port subject to the request for admission or release. Command TLV: The Command TLV is defined in Section 4.4 of . It MUST be present. It MAY appear multiple times. As indicates, the contents of the Command Info field within the Command TLV are specific to the message in which the TLV occurs. For the Multicast Replication Control Message, these contents consist of: a Command Code field; an Accounting field; an instance of the Multicast-Flow TLV. illustrates the complete Command TLV with the contents specific to the Multicast Replication Control message.

Command directive: 1 – Add; 2 – Delete; 3 – Delete All; 4 – Admission Control Reject; 5 – Conditional Access Reject; 6 – Admission Control and Conditional Access Reject. Directives 4 through 6 are used as described in . Meaningful only when the Command Code is "Add" (1). In that case, 0x00 indicates no flow accounting, 0x01 indicates that octet accounting for the flow is to commence. The Accounting field MUST be set to 0x00 for other Command Code values. Reserved for future use. MUST be set to 0x0000 by the sender and ignored by the receiver. An instance of the Multicast-Flow TLV () specifying the flow to be added or deleted. The Multicast-Flow TLV MUST be omitted if the Command Code has value "Delete All" (3). No other embedded TLVs are currently specified within the Multicast Replication Control message/Command TLV. However, see the description of the Multicast Admission Control message (). Unrecognized embedded TLVs SHOULD be silently discarded. The figure below is an example of a Multicast Replication Control message that would result in a swap from multicast Source-Specific Multicast (SSM) flows 2001:DB8::1, FF34::2, to 2001:DB8::2, FF34::3 on the Target identified by the “Access Loop Circuit ID”:

The NAS MAY issue a Multicast Replication Control message to the AN to convey one or more directives to add (join) or delete (leave) one or more multicast flows. The NAS MAY send this message on its own initiative to support the NAS initiated Multicast Control use case presented in and summarized in . In that case, the NAS MUST set the Result field to AckAll (0x2) or Nack (0x1) according to its requirements. The NAS MAY also send this message in response to a Multicast Admission Control message (defined in ) received from the AN to support the conditional access and admission control use case presented in and summarized in . In that case, the NAS MUST set the Result field to NAck (0x1). In either case, the sender MUST populate the Result Code field with the value 0x000 and the ANCP Transaction Identifier field with a unique value, as described in Section 3.6.1.6 of . Each Multicast Replication Control Message MUST contain one or more commands, each encapsulated in its own Command TLV. The sender MUST use a separate Command TLV for each distinct multicast flow. When the order of processing of two commands does not matter, the commands MUST be transmitted in separate Multicast Replication Control messages.

When successive commands (in the same or different messages) relate to the same Target and multicast flow, the state of each feature controlled or affected by attributes received in the Multicast Replication Control message, SHALL be as set by the last command or message referring to that target and flow and containing the controlling attribute. As an example, successive Multicast Replication Control messages containing add commands for a given port and flow, but differing only in the Accounting field setting SHALL be interpreted to mean that the state of the accounting feature is as set in the final command received, but all other features are as set in the initial message. If more than one Command TLV is present in a Multicast Replication Control message, the AN MUST act on the commands in the order in which they are presented in the message. The AN SHALL assign a sequence number to each command in a given Multicast Replication Control message, starting from 0x01 for the first command. If a Command TLV adds a flow and the AN is performing admission control for Multicast Replication Control messages, then the AN MUST perform admission control before replicating the flow. If the admission control check fails, the AN MUST treat the failure as an error as described below. The appropriate Result Code value for the response is 0x013 "Out of resources". If the AN processes the complete Multicast Replication Control message successfully and the Result field of the Multicast Replication Control message was set to AckAll (0x2), the AN MUST respond with a Generic Response message where the Result field is set to Success (0x3), the Result Code field is set to 0x000, and the Transaction Identifier field is copied from the Multicast Replication Control message. The body of the response MAY be empty or MAY be copied from the Multicast Replication Control message. If the AN processes the complete Multicast Replication Control message successfully and the Result field of the Multicast Replication Control message was set to Nack (0x1), the AN MUST NOT respond to the message. The processing/execution of multiple commands contained in a single Multicast Control message MUST be interrupted at the first error encountered, and the remaining commands in the Multicast Replication Control message discarded. If the AN detects an error in a received Multicast Replication Control message and the Result field in that message was set to Nack (0x1) or AckAll(0x2), the AN MUST generate a Generic Response message providing error information to the NAS. This specification identifies the following new Result Code values beyond those specified in , which MAY be used in a Generic Response sent in reply to a Multicast Replication Control message: Command error. Where detected: ANCP agent at the AN. Further description: an invalid command code has been received. Required additional information in the message: see below. Target: ANCP agent at the NAS. Action RECOMMENDED for the receiving ANCP agent: Correct the error and re-send the request, if possible. Otherwise, report the error to the control application with an indication of the erroneous information associated with the invalid TLV(s). Invalid flow address. Where detected: ANCP agent at the AN. Further description: either inconsistent flow address information has been provided or the address family is unsupported. Required additional information in the message: see below. Target: ANCP agent at the NAS. Action RECOMMENDED for the receiving ANCP agent: correct the error and re-send the request, if possible. Otherwise, report the error to the control application with an indication of the erroneous information associated with the invalid TLV(s). Multicast flow does not exist. Where detected: control application at the AN. Further description: the NAS has attempted to delete a flow that is not active on the given access line. Required additional information in the message: see below. Target: control application at the NAS. Action RECOMMENDED for the receiving ANCP agent: report the error to the control application with an indication of the erroneous information associated with the invalid TLV(s). A Generic Response message responding to the Multicast Replication Control message and containing one of the above Result Code values MUST include a Status-Info TLV which includes one or two embedded TLVs as follows: a Sequence-Number TLV as described in , giving the sequence number of the failed command, MUST be included; the failed Command TLV itself SHOULD be included. Note that the Error Message field of the Status-Info TLV MAY be used to report more details than implied by the Result Code value in the message header. For example, the Result Code value could be 0x65 and the Error Message field could contain the text: "Source address present for ASM flow".

This section defines a new message called the Multicast Admission Control message. The Multicast Admission Control message is sent by the AN to the NAS to request admission of a multicast flow, or to notify of the removal of a multicast flow, for a given target. The Message Type for the Multicast Admission Control message is 145. The ANCP Multicast Admission Control message payload contains two TLVs: Target TLV: The Target TLV is defined in . It MUST appear once and only once in the Multicast Admission Control message. It is encoded as specified in or extensions and identifies the AN port subject to the request for admission or release. Command TLV: The Command TLV is defined in . It MUST be present. If it appears more than once, only the first instance is considered meaningful in the present version of this specification and the other instances are ignored. Note: In the future, the specification of the Admission Control message may be extended to allow transport of more than a single directive (e.g., to carry both a leave from one group and a join to another group for the same Target). It is expected that this would support a similar notion of strict sequenced processing as currently defined for handling multiple directives in the Multicast Replication Control message whereby all directives following the first directive that can not be executed are not executed either. When the strict sequenced processing of the directives is not required the directives are distributed across separate messages. The Command TLV has the same contents as were described above for the Multicast Replication Control message, with the following additions: a Request-Source-IP TLV MAY be appended to the Command TLV as an additional embedded TLV; similarly, a Request-Source-MAC TLV MAY be appended to the Command TLV as an additional embedded TLV. Note that the Command TLV length includes the length of any embedded TLVs, including the embedded TLV headers.

The AN sending the Multicast Admission Control message MUST set the Result field to Ignore (0x0). The AN MUST populate the ANCP Transaction Identifier field with a unique value, as described in Section 3.6.1.6 of . The AN MUST encode the Command TLV as specified in with the following additional rules: the Accounting field MUST be set to 0; the Command Code field MUST be set to "1 - Add" when the message conveys a Join , to "2 - Delete" when the message conveys a Leave and to "3 - Delete All" when the message conveys a Leave of all channels (on the target); The Multicast-Flow TLV within the Command TLV identifies the multicast flow subject to the request for admission or release. When the Command Code is 3, the Multicast-Flow TLV is meaningless and MUST be omitted. the Request-Source-IP embedded TLV MAY be included by the AN to convey the IP address of the sender of the join/leave message (e.g., IGMP/MLD Join/Leave) that triggered the AN to include the corresponding Command TLV in the Admission Control message. If it appears more than once, only the first instance is considered meaningful and the other instances are ignored. the Request-Source-MAC embedded TLV MAY be included by the AN to convey the MAC address of the sender of the join/leave message (e.g., IGMP/MLD Join/Leave) that triggered the AN to include the corresponding Command TLV in the Admission Control message. If it appears more than once, only the first instance is considered meaningful and the other instances are ignored.

On receipt of an Multicast Admission Control message, the NAS: MUST ignore the Result field; if the directive in the Multicast Admission Control message is "2 - Delete" or "3 - Delete All" and is processed correctly by the NAS, the NAS MUST NOT generate any ANCP message in response to the Multicast Admission Control message; if the directive in the Multicast Admission Control message is "1 - Add" and is accepted by the NAS, the NAS MUST generate a Multicast Replication Control in response to the Multicast Admission Control message. The Multicast Replication Control message: MUST contain a Result set to Nack (0x1); MUST contain a Transaction ID with a unique value, as described in Section 3.6.1.6 of ; MUST contain the directive as accepted by the NAS. The NAS MAY modify the Accounting field if flow accounting is required. if the directive in the Multicast Admission Control message is "1 - Add", is processed correctly but not accepted by the NAS (i.e., it does not pass the admission control or conditional access check), the NAS MAY generate a Multicast Replication Control message in response to the Multicast Admission Control message. This optional message can be used by the AN to maintain statistics about admission control rejections. In the future, the AN may be able to notify the subscriber that the request was rejected (e.g., using ). When used in this situation, the Multicast Replication Control message: MUST contain a Result set to 0x0; MUST contain a Transaction ID with a unique value, as described in Section 3.6.1.6 of ; MUST contain the directive rejected by the NAS (i.e., Target TLV and Command TLV) but with a Command Code set to "4 - Admission Control Reject", "5 - Conditional Access Reject", or "6 - Admission Control and Conditional Access Reject" as applicable. if the Multicast Admission Control message cannot be processed correctly by the NAS (e.g. the message is malformed, the multicast flow does not exist etc.), the NAS MUST generate a Generic Response message (defined in Section 4.2 of ) with appropriate content indicating the reason for the failure.

The Bandwidth Reallocation Request message is used when the bandwidth delegation capability is included in the negotiated set. It MAY be sent either by the NAS or by the AN to request an adjustment in the amount of delegated bandwidth. It will be sent by the NAS typically to reduce the multicast bandwidth allocated to the AN in order for the NAS to satisfy a request to add one or more flows. Conversely, the AN will send a Bandwidth Reallocation Request to obtain additional bandwidth to satisfy a request to add a multicast channel. In each case, the requestor has a minimum requirement for additional bandwidth, and MAY ask for additional bandwidth beyond this amount (e.g., to handle anticipated future requests). The Bandwidth Reallocation Request message contains two TLVs: the Target TLV (Section 4.3 of or an extension), specifying a single access line; the Bandwidth-Request TLV (), specifying the required and preferred amounts of delegated bandwidth. The Message Type for the Bandwidth Reallocation Request message is 146.

The Result field in the header of the Bandwidth Reallocation Request message is not used and the sender MUST set it to Ignore (0x0). The bandwidth values in the Bandwidth-Request TLV are expressed in terms of total multicast bandwidth allocated to the AN. The choice of "total bandwidth" rather than "incremental bandwidth" was made so that it would be easier for the AN and NAS to keep their respective views of the current amount of delegated bandwidth synchronized. Because the values are totals rather than desired increments/decrements, the relationship between the required amount and the preferred amount will differ depending on whether the Bandwidth Reallocation Request message is issued by the NAS or the AN. If the NAS is making the request, the preferred amount MUST be less than or equal to the required amount. The required amount MUST be less than the current amount of delegated bandwidth. If the AN is making the request, the preferred amount MUST be greater than or equal to the required amount. The required amount MUST be greater than the current amount of delegated bandwidth.

When the peer receives a valid Bandwidth Reallocation Request message, it SHOULD determine whether it can satisfy the request from its existing allocation of unused video bandwidth. If it decides that it can reallocate bandwidth to the peer, it MAY choose to return any amount between the required and the preferred amounts indicated in the Bandwidth Reallocation Request message. The peer MUST return a Bandwidth Transfer message () indicating its decision. If the request is met, the Result field of the Bandwidth Transfer message MUST be set to Success (0x3), the Result Code field MUST be set to 0x000, and the Bandwidth-Allocation TLV () MUST contain the new value of total multicast bandwidth. This new value MUST lie between the required and preferred values, inclusive, from the request message. If the request is not met, the Result field of the Bandwidth Transfer message MUST be set to Failure (0x4), the Result Code field MUST be set to 0x000, and the Bandwidth Allocation TLV MUST contain the value of the currently allocated amount of delegated bandwidth as the responder views it. The following cases indicate that the sender holds a different view of the amount of delegated bandwidth from the receiver: the NAS receives a request where the required amount is less than its view of the current amount of delegated bandwidth; the AN receives a request where the required amount is greater than its view of the current amount of delegated bandwidth. If one of these cases occurs, the receiver with one exception MUST send a Bandwidth Transfer message indicating Success. If the NAS received the request, the allocated amount in the NAS's response MUST be at least equal to NAS's view of the current amount of delegated bandwidth. If the AN received the request, the allocated amount in the AN's response MUST be no greater than the AN's view of the current amount of delegated bandwidth. The exception is when the NAS receives a request while it has a request of its own outstanding. Handling of that case is described below. While the cases just described are an error condition, the success response achieves a graceful recovery. To avoid deadlock due to race conditions, the following rules MUST be applied: If the NAS receives a Bandwidth Reallocation Request message while it has a Bandwidth Reallocation Request message of its own outstanding for the same access line, the NAS MUST provide an immediate failure response to the request from the AN, with a Result Code value set to 0x68 "Inconsistent views of delegated bandwidth amount" or 0x69 "Bandwidth request conflict" as applicable. (See below for more information). If the AN receives a Bandwidth Reallocation Request message while it has a Bandwidth Reallocation Request message of its own outstanding for the same access line, the AN MUST release any bandwidth it has already committed to an outstanding Join request while it is awaiting a response from the NAS. It MUST decide upon and send its response to the NAS taking the released bandwidth into account. If the receiver is unable to process the Bandwidth Reallocation Request message due to an error, then the receiver MUST return a Bandwidth Transfer message where: the Result field is set to Failure (0x4), the Result Code field is set appropriately to indicate the type of error that was detected, the Bandwidth Allocation TLV contains the value of the current amount of delegated bandwidth as the responder views it, and a Status-Info TLV MAY follow the Bandwidth Allocation TLV giving further information about the error. This specification provides three new Result Code values applicable specifically to the contents of the Bandwidth-Request TLV. These Result Code values by their nature MUST only be used when the error is being reported in a Bandwidth Transfer message rather than a Generic Response message. Invalid preferred bandwidth amount. Where detected: control application at the receiver of the Bandwidth Reallocation Request message. Further description: the preferred and required amounts of bandwidth in the TLV do not have the numerical relationship described above. Required additional information in the message: as described above. Target: control application at the sender of the Bandwidth Reallocation Request message. Action RECOMMENDED for the receiving ANCP agent: report the error to the control application with the returned value of the Bandwidth-Allocation TLV. See also . Inconsistent views of delegated bandwidth amount. Where detected: control application at the NAS. Further description: the NAS has an outstanding Bandwidth Reallocation Request, so it is rejecting a similar request from the AN. In the AN request, the required amount was less than the NAS's view of the current amount of delegated bandwidth. Required additional information in the message: as described above. Target: control application at the AN. Action RECOMMENDED for the receiving ANCP agent: report the error to the AN control application with the returned value of the Bandwidth-Allocation TLV. See also . Bandwidth request conflict. Where detected: control application at the NAS. Further description: the NAS has an outstanding Bandwidth Reallocation Request, so it is rejecting a similar, valid request from the AN. Required additional information in the message: as described above. Target: control application at the AN. Action RECOMMENDED for the receiving ANCP agent: report the error to the AN control application with the returned value of the Bandwidth-Allocation TLV. See also .

The Bandwidth Transfer message is used to transfer video bandwidth from the sender to the peer for a specific access line. This message MAY be sent either from the AN or from the NAS. As described in the previous section, it is the required response to a valid Bandwidth Reallocation Request message. The Bandwidth Transfer message MAY also be used to transfer bandwidth autonomously from one peer to another. One example of this usage is to release bandwidth borrowed earlier by means of the Bandwidth Reallocation Request message. When the message is used in this way, the Result field in the Bandwidth Transfer message MUST be set to Ignore (0x0). This allows the receiver to distinguish between an autonomous transfer and a response to a previous Bandwidth Reallocation Request, for purposes of validation. The Message Type for the Bandwidth Transfer message is 147. The Bandwidth Transfer message contains the following TLVs: the Target TLV, designating the access line concerned; an instance of the Bandwidth-Allocation TLV (). The bandwidth value in the Bandwidth-Allocation TLV is the new amount of delegated bandwidth allocated to the target.

When sending a Bandwidth Transfer message where the Result value is Ignore (0x0) or Success (0x3), the following relationships MUST hold: if the message is sent by the NAS, the bandwidth value in the Bandwidth-Allocation TLV MUST be greater than or equal to the sender's view of the current amount of delegated bandwidth for the access line concerned; if the message is sent by the AN, the bandwidth value in the Bandwidth-Allocation TLV MUST be less than or equal to the sender's view of the current amount of delegated bandwidth for the access line concerned. Further sender behaviour is specified above, in .

If the amount of delegated bandwidth provided in the Bandwidth-Allocation TLV is not greater than the NAS's view of the current amount of delegated bandwidth, the NAS MUST update its view of the current amount of delegated bandwidth to the amount indicated in the Bandwidth Transfer message. This is required regardless of whether the Result field of that message indicates Success or Failure. If the amount of delegated bandwidth provided in the Bandwidth-Allocation TLV is greater than the NAS's view of the current amount of delegated bandwidth, the NAS MAY accept the given value as its new value of delegated bandwidth. Alternatively, the NAS MAY force the AN to modify its view of the amount of delegated bandwidth to that held by the NAS, by sending a Port Management message for the target access line concerned, containing a Bandwidth-Allocation TLV with a value equal to the amount of delegated bandwidth the NAS wishes to enforce.

If the amount of delegated bandwidth provided in the Bandwidth-Allocation TLV of the Bandwidth Transfer message differs from the AN's view of the current amount of delegated bandwidth, the AN MUST update its view of the current amount of delegated bandwidth to the amount indicated in the Bandwidth Transfer message. This is required with the exception of a Bandwidth Transfer message with a Result field equal to Failure (0x4) and a Result Code field equal to 0x68 "Inconsistent views of delegated bandwidth amount" or 0x69 "Bandwidth request conflict". If Result Code value 0x68 is received, the AN MUST issue a Delegated Bandwidth Query Request message to determine the NAS's current view of the amount of delegated bandwidth. The AN MUST update its own view based on the value returned in the Delegated Bandwidth Query Response. If Result Code value 0x69 is received, the AN SHOULD carry out this procedure unless it can account for the discrepancy as a result of a transfer of bandwidth to the NAS that was carried out just before the incoming Bandwidth Transfer message was processed. The two Result Code values indicate a race condition where the AN may have just completed a transfer of bandwidth to the NAS. As a result, the value given in the Bandwidth Transfer message may be outdated, and the AN needs to query the NAS to find its latest view. The procedure assumes that ordering is preserved between the Bandwidth Transfer message sent by the AN in response to the NAS's request and the subsequent Delegated Bandwidth Query Request message. If as the result of the procedures just described the AN determines that it has over-committed multicast bandwidth, it MUST NOT terminate any currently-active programs, but MUST NOT honour any more "join" requests until it is possible to do so within the limit set by its current value of delegated bandwidth.

The Message Type for the Delegated Bandwidth Query Request (and Response) messages is 148. The Delegated Bandwidth Query Request message MAY be sent either by the NAS or by the AN to retrieve the peer's view of the amount of delegated bandwidth. The request contains one TLV: a Target TLV designating the access line for which the information is requested.

The sender MUST set the Result field in the header of the Delegated Bandwidth Query Request message to AckAll (0x2). The Result Code value MUST be set to 0x000. The sender MUST populate the ANCP Transaction Identifier field with a unique value, as described in Section 3.6.1.6 of .

If the AN or NAS receives a valid Delegated Bandwidth Query Request message, it MUST respond with a Delegated Bandwidth Query Response message. The Result field in the header of the response MUST be set to Success (0x3). The Result Code field MUST be set to 0x000. The Transaction-Id field MUST be copied from the request message. The body of the response MUST contain the Target TLV, copied from the request message. Finally, the body of the response MUST contain a Bandwidth-Allocation TLV, containing the current amount of delegated bandwidth from the point of view of the receiver of the request. If the contents of the Delegated Bandwidth Query Request message are in error, the receiver MUST return a Delegated Bandwidth Query Response message with the Result field in the header set to Failure (0x3). The Result Code field MUST be set to the value that indicates the nature of the error (e.g., 0x500 "One or more of the specified ports do not exist"). The Transaction-Id field MUST be copied from the request. The body of the response MUST contain the Target TLV copied from the request. This MAY be followed by a Status-Info TLV giving further information about the error.

The Delegated Bandwidth Query Response message is sent in reply to a Delegated Bandwidth Query Request. The response to a valid request contains two TLVs: the Target TLV, copied from the request; a Bandwidth-Allocation TLV, giving the responder's view of the current amount of multicast bandwidth delegated to the AN. The Message Type for the Delegated Bandwidth Query Response message is 148.

Sender behaviour for the Delegated Bandwidth Query Response message is specified in .

If the Delegated Bandwidth Query Response message indicates Success (0x3), the following actions apply.

If the amount of delegated bandwidth provided in the Bandwidth-Allocation TLV is less than the NAS's view of the current amount of delegated bandwidth, the NAS MUST update its view of the current amount of delegated bandwidth to the amount indicated in the Delegated Bandwidth Query Response message. If the amount of delegated bandwidth provided in the Bandwidth-Allocation TLV is greater than the NAS's view of the current amount of delegated bandwidth, the NAS MAY accept the given value as its new value of delegated bandwidth. Alternatively, the NAS MAY force the AN to modify its view of the amount of delegated bandwidth to that held by the NAS, by sending a Port Management message for the target access line concerned, containing a Bandwidth-Allocation TLV with a value equal to the amount of delegated bandwidth the NAS wishes to enforce.

The AN SHOULD accept the value returned in the Bandwidth-Allocation TLV of the Delegated Bandwidth Query Response message as the correct value of the current amount of delegated bandwidth. If the AN has currently committed more than this amount to active programs, it MUST NOT cease replicating the flows concerned, but MUST NOT honour any more Join requests until possible to do so within the new limit. A race condition is possible, where the AN sends a query, the NAS requests more bandwidth, then receives and responds to the query, then receives the Bandwidth Transfer message responding to its request. It is up to the AN to take appropriate action in this case. The best action appears to be not to act on the result of the first query, but to repeat the query after sending the Bandwidth Transfer message. Similar considerations apply to a race between queries from both sides.

This section defines two new messages called the Multicast Flow Query Request and Multicast Flow Query Response. The Multicast Flow Query Request is sent by the NAS to request information about the multicast flows that are active on the AN. The Multicast Flow Query Response is sent in response by the AN to provide the requested information to the NAS. The Message Type for the Multicast Flow Query Request and Multicast Flow Query Response messages is 149. The contents of the Multicast Flow Query Request and Response depend on the nature of the query, as described below.

The sender of a Multicast Flow Query Request message MUST set the Result field to AckAll (0x2). The Result Code field MUST be set to 0x000. The sender MUST populate the ANCP Transaction Identifier field with a unique value, as described in section 3.6.1.6 of . The Multicast Flow Query Request MAY be used by the NAS to retrieve: the AN's view of which multicast flows are currently active on a specified set of access ports; or the AN's view of the access ports on which a specified set of multicast flows are currently active; or the AN's view of all the multicast flows currently active on each access port of the AN. To retrieve the AN's view of which multicast flows are currently active on a given port of the AN, the NAS MUST include a Target TLV in the Multicast Flow Query Request payload identifying that port. The Target TLV is encoded as specified in . To retrieve the AN's view of the ports currently receiving a given multicast flow, the NAS MUST include a Multicast-Flow TLV in the Multicast Flow Query Request payload identifying that flow. The Multicast-Flow TLV is encoded as specified in . The NAS MAY include multiple Target TLVs or multiple Multicast-Flow TLVs in the Multicast Flow Query Request, but MUST NOT include both Target and Multicast-Flow TLVs in the same message. To retrieve the AN's view of all of the multicast flows currently active on each port of the AN, the NAS MUST send a Multicast Flow Query Request which does not contain any instance of the Target TLV or the Multicast-Flow TLV.

The AN MUST respond to a Multicast Flow Query Request message that has a valid format and a valid content with a Multicast Flow Query Response message. The Result field in the response MUST be set to Success (0x3). The Result Code field MUST be set to 0x000. The Transaction-Id field MUST be copied from the request. If the Multicast Flow Query Request contained one (or more) Target TLVs, the AN MUST include, for each of these Target TLVs, the following set of TLVs: Target TLV. This MUST be identical to the Target TLV in the received Multicast Flow Query Request message. Multicast-Flow TLV(s). The Multicast-Flow TLV MUST appear once per multicast flow that is currently active on the AN port identified in the preceding Target TLV. The Target TLVs MUST appear in the response from the AN in the same order as in the query from the NAS. If the Multicast Flow Query Request contained one (or more) Multicast-Flow TLVs, the AN MUST include, for each of these Multicast-Flow TLVs, the following set of TLVs: Multicast-Flow TLV. This MUST be identical to the Multicast-Flow TLV in the received Multicast Flow Query Request message. Target TLV(s). The Target TLV MUST appear once per AN port on which the multicast flow identified in the preceding Multicast-Flow TLV is active. The Multicast-Flow TLVs MUST appear in the response from the AN in the same order as in the query from the NAS. If the Multicast Flow Query Request contained no Target TLV and no Multicast Flow TLV, the AN MUST include, for each AN port currently receiving multicast flow(s), the following set of TLVs: Target TLV. This MUST identify one AN port. Multicast-Flow TLV(s). The Multicast-Flow TLV MUST appear once per Multicast Flow that is currently active on the AN port identified in the preceding Target TLV. If the contents of the Multicast Flow Query Request are in error, the AN MUST reply with a Multicast Flow Query Response message with the Result field set to Failure (0x4) and the Result Code field set to indicate the nature of the error. If the request contained multiple instances of the Target TLV or the Multicast-Flow TLV and one of these is in error, the response message MUST contain the results for the preceding instances of the TLV as if there had been no error. These successful results MUST be followed by the TLV in error, copied from the request. The AN MUST NOT do further processing of the request. The AN MAY add a Status-Info TLV to provide further information on the nature of the error.

This section describes the Committed Bandwidth Report message, which is sent from the AN to the NAS to report the most recent amount of multicast bandwidth usage committed to one or more access lines. The Message Type for the Committed Bandwidth Report message is 150. The Committed Bandwidth Report message contains one or more instances of the Committed-Bandwidth TLV, as described in .

The sender of a Committed Bandwidth Report message MUST set the Result field to Ignore (0x0). The Result Code field MUST be set to 0x000. The sender MUST populate the ANCP Transaction Identifier field with a unique value, as described in section 3.6.1.6 of . Each instance of the Committed-Bandwidth TLV included in the message MUST identify an access line for which the amount of committed multicast bandwidth has changed since the previous Committed Bandwidth Report message was sent and MUST report the latest amount of multicast bandwidth committed to that line. There MUST be only one instance of the Committed-Bandwidth TLV present in the message for any given access line. The message MUST include an instance of the Committed-Bandwidth TLV for every access line for which committed multicast bandwidth has changed since the previous Committed Bandwidth Report message was sent. Further behaviour at the AN is specified in .

The usage of the contents of a Committed Bandwidth Report message received by the NAS is implementation-dependent. One example is that the NAS uses the reports of multicast bandwidth commitments to adjust its forwarding scheduler operation to provide the intended level of QoS. The NAS MUST NOT reply to a valid Committed Bandwidth Report message. The NAS MAY send a Generic Response message indicating the nature of any errors detected in a Committed Bandwidth Report message that it has received.

This section defines new ANCP TLVs for the control of multicast flows.

This document defines the new Multicast-Service-Profile TLV. The Multicast-Service-Profile TLV MAY be included in a Provisioning message as specified in . The Multicast-Service-Profile TLV is illustrated in . It consists of a TLV header encapsulating a single instance of the Multicast-Service-Profile-Name TLV and one or more instances of the List-Action TLV.

The Multicast-Service-Profile TLV has the following fields: The Multicast-Service-Profile TLV Type is 0x0013. The TLV length is determined by the contents following the TLV header. The Multicast-Service-Profile-Name TLV is described in . The Multicast-Service-Profile-Name TLV MUST contain an identifier which is unique over all profiles provisioned to the same AN partition. This identifier will be used to refer to the profile when activating it for a given target within a Port Management message (see ). The List-Action TLV is described in . The List-Action TLV(s) provide the content of a newly defined multicast service profile or modify the existing content. If more than one List-Action TLV is present, the order of the TLVs may be significant, since List-Action TLVs are processed in the order in whch they appear.

The Multicast-Service-Profile-Name TLV carries the identifier of a multicast service profile provisioned on the AN. It is illustrated in .

The Multicast-Service-Profile-Name TLV has the following fields: The Multicast-Service-Profile-Name TLV Type is 0x0018. TLV Length: up to 255 octets. Multicast service profile identifier: an opaque sequence of octets identifying a specific multicast service profile. The identifier could have the form of human-readable text or an arbitrary binary value, depending on the operator's practices.

The List-Action TLV identifies multicast flows to be added to or removed from a list of white-, black-, or grey-listed flows. It is meaningful only in association with a Multicast-Service-Profile-Name TLV identifying the profile to which the List-Action TLV applies. Such an association can be achieved by placing both TLVs in the same base message payload or as embedded TLVs of another TLV such as the Multicast-Service-Profile. The List-Action TLV is shown in .

The List-Action TLV contains the following fields: The List-Action TLV Type is 0x0021. TLV Length: length of the subsequent contents. Operation: operation to be performed upon the white, black, or grey list identified by the List Type field within the profile identified by the associated Multicast-Service-Profile-Name embedded TLV. The possible values are: Add (0x01): the multicast flow fields are to be added to the list. Delete (0x02): the multicast flow fields are to be removed from the list. Each multicast flow field in the List-Action MUST match exactly an existing entry in the list concerned. Thus to remove part of the range provided by a wildcarded list entry, it is necessary to remove the entire entry and add back the remaining partial range(s). Replace (0x03): the multicast flow fields replace the existing contents of the list. List Type: the list type being modified by this List-Action. The possible values are White (0x01), Black (0x02), or Grey (0x03). Reserved: a sender MUST set this field to 0x0000. A receiver MUST ignore the contents of this field. Address Family: the IP version of the set of multicast flow fields that follow, encoded according to . Possible values are 0x0001 (IPv4) or 0x0002 (IPv6). Either an IPv4 list or an IPv6 list or both MAY be present in the List-Action TLV. Number of flow fields: the number of multicast flow fields of the given address family which follow. Multicast flow field: a field identifying one or more multicast flows. It consists of an 8-bit group address prefix length, an 8-bit source address prefix length, a 0-16 octet group prefix, and a 0-16 octet source prefix, as shown in . Each multicast flow field refers either to a Source-Specific Multicast (SSM) channel or to an Any Source Multicast (ASM) group. The scope of the designation may be broadened to multiple channels or groups through use of prefix length values smaller than the total address length for the given address family. Multicast flow fields MUST be placed consecutively within the embedded TLV without intervening padding except to round out individual addresses to the nearest octet boundary. A multicast flow field consists of two single-octet prefix lengths followed by zero to two prefix values as shown in :

The prefix length has its usual meaning. It is the number of most-significant bits specified within the corresponding prefix. The prefix length MAY vary from 0 to 32 in the IPv4 sub-list, and from 0 to 128 in the IPv6 sub-list. A value of 0x00 for either the Group PrefLen (prefix length) or the Source PrefLen indicates that any value of the corresponding address will match (wild card). If the value 0x00 is provided for a particular prefix length, the corresponding prefix MUST be omitted from the field contents. The length of a Source or Group Prefix field is equal to (PrefLen + 7)/8 octets, truncated to the nearest integer. Unused bits at the end of the prefix MUST be set to zeroes.

The Sequence-Number TLV conveys a sequence number of some sort. The specific meaning of the sequence number is message-specific. Within this specification, the Sequence-Number TLV is used as a embedded TLV in a Status-Info TLV, in a Generic Response reporting a failed command in a Multicast Replication Control or Multicast Admission Request message. It identifies the sequence number within the message of the command that failed. The Sequence-Number TLV has the format shown in .

The Sequence-Number TLV has the following fields: The Sequence-Number TLV Type is 0x0022. TLV length is 0x0004. Sequence number: the sequence number of a specific entity within a series, where numbering starts from 1 for the first entity in the series. Represented as a 32-bit binary number, most significant bit first.

The Bandwidth-Allocation TLV is used to indicate the total amount of video bandwidth delegated to the AN for multicast admission control for a given access line, in kilobits per second. The TLV has the format shown in .

The Bandwidth-Allocation TLV has the following fields: The Bandwidth-Allocation TLV Type is 0x0015. TLV length is 4. Delegated amount: the bandwidth amount delegated to the AN for admission of multicast video on a given port, kilobits per second. Presented as a 32-bit binary value, most significant bit first.

The White-List-CAC TLV is used to indicate that the NAS wishes the AN to do admission control for white-listed flows. Details on when the White-List-CAC TLV may be provisioned are specified in . The White-List-CAC TLV is illustrated in .

The White-List-CAC TLV contains the following fields: The White-List-CAC TLV Type is 0x0024. TLV length is 0, since the TLV contains no data other than the TLV header.

The MRepCtl-CAC TLV is used to indicate that the NAS wishes the AN to do admission control for flows added by the Multicast Replication Control message. Details on when the MRepCtl-CAC TLV may be provisioned are specified in . The MRepCtl-CAC TLV is illustrated in .

The MRepCtl-CAC TLV contains the following fields: The MRepCtl-CAC TLV Type is 0x0025. TLV length is 0, since the TLV contains no data other than the TLV header.

The Bandwidth-Request TLV is used to request an adjustment of the total amount of video bandwidth allocated to the AN for multicast admission control for a given line. The "Required amount" field indicates the minimum adjustment required to meet the request. The "Preferred amount" field indicates the adjustment the requestor would prefer to have, if possible. discusses the required relationships between the "Required amount", "Preferred amount", and current values of total bandwidth allocated to the AN. The Bandwidth-Request TLV has the format shown in .

The Bandwidth-Request TLV has the following fields: The Bandwidth-Request TLV Type is 0x0016. The TLV length is 8 octets. Required amount: the minimum or maximum amount, depending on whether the sender is the AN or the NAS respectively, of delegated video bandwidth that is being requested, in kilobits per second. Presented as a 32-bit binary value, most significant bit first. Preferred amount: the preferred amount of delegated video bandwidth that is being requested, in kilobits per second. Presented as a 32-bit binary value, most significant bit first.

The Request-Source-IP TLV provides the IP address of the entity that originated a specific request to join or leave a multicast channel. The TLV is illustrated in .

The Request-Source-IP TLV contains the following fields: The Request-Source-IP TLV Type is 0x0092. TLV length is 4 for an IPv4 address or 16 for an IPv6 address. Unicast address: IP address of the source of a multicast flow join request, in network byte order.

The Request-Source-MAC TLV provides the MAC address of the entity that originated a specific request to join or leave a multicast channel. The TLV is illustrated in .

The Request-Source-MAC TLV contains the following fields: The Request-Source-MAC TLV Type is 0x0093. TLV length is either 6 octets (MAC-48 or EUI-48) or 8 octets (EUI-64). IEEE MAC Address: MAC address of the device originating the request to join a multicast flow. Within the address, bytes and bits respectively shall be ordered from most to least significant, consistently with for MAC-48 and EUI-48, and with for EUI-64. EUI-48 and EUI-64 are registered trademarks of the IEEE.

The Multicast-Flow TLV specifies a multicast flow in terms of its multicast group address and, if applicable, its unicast source address. It is illustrated in .

The Multicast-Flow TLV has the following fields: The Multicast-Flow TLV Type is 0x0019. TLV Length: ranges from a minimum of 8 (for an ASM IPv4 flow) to 36 (for an IPv6 SSM flow). Flow Type: 0x01 for Any Source Multicast (ASM), 0x02 for Source-Specific Multicast (SSM). Addr Family: address family of the multicast source and group addresses, encoded in accordance with the IANA PIM Address Family registry (). 0x01 indicates IPv4, 0x02 indicates IPv6. Reserved: MUST be set to 0x0000 by the sender and MUST be ignored by the receiver. One possible use for this field in the future is to indicate the presence of PIM Join attributes attached to the source address (see ). The applicability of PIM attributes in the context of ANCP is for further study. Multicast Group Address: a multicast group address within the given address family. The group address MUST always be present. Unicast Source Address: unicast address within the given address family. If the Flow Type is 0x01 (ASM), a source address MUST NOT be present. If the Flow Type is 0x02 (SSM), a source address MUST be present.

The Report-Buffering-Time TLV provides the time for which a Committed Bandwidth Report message must be held with the intention of accumulating multiple reports of changed committed multicast bandwidth in one report, to reduce the volume of messages sent to the NAS. For further information see . The TLV is illustrated in .

The Report-Buffering-Time TLV contains the following fields: The Report-Buffering-Time TLV Type is 0x0094. TLV length is 4 octets. Buffering Time is a 32-bit unsigned integer containing a time value in ms.

The Committed-Bandwidth TLV identifies an access line and provides the current amount of multicast bandwidth that the AN has committed to it. The TLV is illustrated in .

The Committed-Bandwidth TLV contains the following fields: The Committed-Bandwidth TLV Type is 0x0095. TLV length is 4 octets plus the length of the Target TLV including its header and any padding. Committed Multicast Bandwidth is a 32-bit unsigned integer providing a bandwidth amount in kbits/s. The Target TLV identifies the access line to which this amount of multicast bandwidth is currently committed.

Section 3.5 of defines a capability negotiation mechanism as well as a number of capabilities. This section defines five new capabilities in support of different modes of multicast operation: NAS-initiated replication (capability type 3); committed multicast bandwidth reporting (capability type 5); conditional access with white and black lists (capability type 6); conditional access with grey lists (capability type 7); bandwidth delegation (capability type 8). The "Capability Data" field within the Capability TLV for all of these capabilities is empty. All of these capabilities are independent of the access technology. The remainder of this section consists of three sub-sections. specifies the protocol elements that must be implemented in order to support each capability. specifies the procedures that apply to each capability on its own. specifies how the capabilities interact if more than one multicast capability is included in the set of capabilities negotiated between the AN and the NAS. Note that if a request contains content that is not supported (according to the tables in ) by the negotiated set of multicast capabilities, the appropriate response is to return a Generic Response message indicating Failure (0x4) with an appropriate code value. The body of the message MUST contain a Status-Info TLV. See Sections 4.2 and 4.5 in for more details.

This section specifies the protocol elements that MUST be implemented to support each of the four multicast capabilities. Support of multiple multicast capabilities requires implementation of the union of the sets of protocol elements applying to each of the individual capabilities in the supported set. In addition to the elements listed below, implementation of the Target TLV (Section 4.3 of ) is REQUIRED for all of the capabilities specified in this document.

specifies the protocol elements within and that MUST be implemented to support the NAS-initiated replication multicast capability. Additionally, implementation of the Multicast Replication Control message requires implementation of the Command TLV (Section 4.4 of with additional details in of this document). Reference Protocol Element Provisioning message with MRepCtl-CAC TLV Port Management message with Bandwidth-Allocation TLV. Multicast Replication Control message Multicast Flow Query Request and Response messages Sequence Number TLV Bandwidth-Allocation TLV MRepCtl-CAC TLV Multicast-Flow TLV

specifies the protocol elements within and that MUST be implemented to support the committed multicast bandwidth reporting capability. Reference Protocol Element Provisioning message with Report-Buffering-Time TLV Committed Bandwidth Report message Multicast Flow Query Request and Response messages Report-Buffering-Timer TLV Committed-Bandwidth TLV Multicast-Flow TLV

specifies the protocol elements within and that MUST be implemented to support the conditional access with white and black lists multicast capability. Reference Protocol Element Provisioning message with Multicast-Service-Profile TLV, white and black lists only, and White-List-CAC TLV Port Management message with Multicast-Service-Profile-Name and Bandwidth-Allocation TLVs. Multicast Flow Query Request and Response messages Multicast-Service-Profile TLV Multicast-Service-Profile-Name TLV List-Action TLV, white and black lists only Bandwidth-Allocation TLV White-List-CAC TLV Multicast-Flow TLV

specifies the protocol elements within and that MUST be implemented to support the conditional access with grey lists multicast capability. Additionally, implementation of the Multicast Replication Control message requires implementation of the Command TLV (Section 4.4 of with additional details in of this document). Reference Protocol Element Provisioning message with Multicast-Service-Profile TLV, grey lists only, and MRepCtl-CAC TLV Port Management message with Multicast-Service-Profile-Name and Bandwidth-Allocation TLVs. Multicast Replication Control message Multicast Admission Control Message Multicast Flow Query Request and Response messages Multicast-Service-Profile TLV, grey lists only Multicast-Service-Profile-Name TLV List-Action TLV, grey lists only Sequence Number TLV Bandwidth-Allocation TLV MRepCtl-CAC TLV Request-Source-IP TLV Request-Source-MAC TLV Multicast-Flow TLV

specifies the protocol elements within and that MUST be implemented to support the delegated bandwidth multicast capability. Reference Protocol Element Port Management message with Bandwidth-Allocation TLV. Bandwidth Reallocation Request Message Bandwidth Transfer Message Delegated Bandwidth Query Request Message Delegated Bandwidth Query Response Message Multicast Flow Query Request and Response messages Bandwidth-Allocation TLV Bandwidth-Request TLV Multicast-Flow TLV

This section describes multicast service procedures for each capability as if it were the only multicast capability within the negotiated set. Procedures involving combinations of multicast capabilities are described in . The use of the Multicast Flow Query Request and Response messages to determine the association between multicast flows and ports is common to all multicast capabilities. No additional text is required here, beyond that already given in to describe the use of those messages.

NAS-initiated replication may be negotiated to support a mode of operation where IGMP/MLD requests are terminated on the NAS. Alternatively, it may be negotiated to allow the NAS to respond to requests sent by other means (e.g., through application signalling) that require the replication of multicast channels to a given access line.

The NAS MAY perform admission control for NAS-initiated replication. In this case, it MUST NOT include the MRepCtl-CAC TLV in a Provisioning message sent to the AN. Alternatively, the NAS MAY enable admission control at the AN for NAS-initiated replication. To do this, it MUST include the MRepCtl-CAC TLV in a Provisioning message sent to the AN and it MUST also include a Bandwidth-Allocation TLV in a Port Management message for each access line.

The procedures associated with NAS-initiated replication are straightforward. To initiate replication, the NAS MUST send a Multicast Replication Control message to the AN, containing one or more commands adding flows, as described in . To terminate replication the NAS MUST send a Multicast Replication Control message where the commands delete instead of adding the flows. The AN acts upon these messages as specified in .

Committed bandwidth reporting may be negotiated if the NAS requires current knowledge of the amount of multicast bandwidth committed to each access line and cannot obtain this information by other means.

The default buffering time when committed bandwidth reporting is enabled is zero (immediate reporting). To change this, the NAS MAY send an instance of the Report-Buffering-Time TLV containing a non-zero time value to the AN in a Provisioning message. If the NAS subsequently wishes to change the buffering time again, it MAY do so in another Provisioning message.

If the buffering time for committed bandwidth reporting is zero, the AN MUST send a Committed Bandwidth Report message to the NAS each time the amount of multicast bandwidth committed to any access line under its control changes. If a non-zero value is provided in the Report-Buffering-Time TLV, the AN at any given moment is in one of two states: not-buffering, or buffering. The AN enters buffering state if it is in not-buffering state and the multicast bandwidth amount committed to some access line changes. It leaves buffering state when the AN sends a Committed Bandwidth Report. Upon entry to the buffering state, the AN MUST start a buffering timer and create a Committed Bandwidth Report message containing a Committed-Bandwidth TLV for the triggering access line, but MUST NOT send it. If a multicast bandwidth change occurs for another access line, the AN MUST add a new Committed-Bandwidth TLV to the message for that additional line. If a multicast bandwidth change occurs for a line for which a Committed-Bandwidth TLV is already present in the buffered report, the AN MUST update the corresponding Committed-Bandwidth TLV to contain the new bandwidth value, rather than adding another Committed-Bandwidth TLV for the same access line. The buffering timer expires after the period provided by the Report-Buffering-Time TLV. When it expires, the AN MUST send the Committed Bandwidth Report message that it has been accumulating to the NAS. Exceptionally, the AN MAY choose to send the message before the timer expires, in which case it MUST clear the buffering timer when the message is sent. In either case, the AN enters the not-buffering state as a result. Report buffering implies that NAS reaction to changes in multicast bandwidth usage is delayed by the amount of the buffering period. The choice of buffering period must take this into consideration.

The NAS provisions named multicast service profiles containing white and black lists on the AN using the Provisioning message containing one or more Multicast-Service-Profile TLVs. The NAS MAY update the contents of these profiles from time to time as required, by sending additional Provisioning messages with Multicast-Service-Profile TLVs containing incremental modifications to the existing white and black lists or replacements for them. The NAS assigns a specific multicast service profile to an individual access line using the Port Management message containing a Multicast-Service-Profile-Name TLV. The NAS MAY change the multicast service profile for a given access line at any time by sending a Port Management message identifying a new multicast service profile. The NAS MAY choose to enable admission control at the AN for white-listed flows. To do this, it MUST send a Provisioning message as described in , which includes the White-List-CAC TLV and it MUST provide a multicast bandwidth allocation for each access line by including a Bandwidth-Allocation TLV in a Port Management message.

The conditional access with white and black lists capability assumes that IGMP/MLD requests are terminated on the AN. When the AN receives a "join" request, it MUST check to see whether the requested flow is white-listed or black-listed as described below. Requests for black-listed flows MUST be discarded. If the NAS has enabled admission control on the AN as described in the previous section, but a white-listed flow would cause the amount of committed multicast bandwidth to exceed the provisioned limit, the request MUST be discarded. The AN replicates flows passing these checks to the access line. To determine if a requested flow is white-listed, the AN searches for a best match to the flow in the applicable multicast service profile. Matching is done on the prefixes specified in the profile, ignoring the address bits of lower order than those in the prefix. If the requested multicast flow matches multiple lists associated with the access line, then the most specific match will be considered by the AN. If the most specific match occurs in multiple lists, the black list entry takes precedence over the white list. In this context, the most specific match is defined as: first, most specific match (longest prefix length) on the multicast group address (i.e., on G of <S,G>) then, most specific match (longest prefix length) on the unicast source address (i.e. on S of <S,G>) If the requested multicast flow is not part of any list, the join message SHOULD be discarded by the AN. This default behavior can easily be changed by means of a "catch-all" statement in the white list. For instance, adding (<S=*,G=*>) in the white List would make the default behavior to accept join messages for a multicast flow that has no other match on any list. When the AN receives a "leave" request, it terminates replication of the multicast flow. If the AN receives a Provisioning message which updates an existing multicast service profile, the AN MUST review the status of active flows on all ports to which the updated profile is currently assigned. Similarly, if a Port Management message assigns a new multicast service profile to a given port, the AN MUST review all active flows on that port. If the most specific match for any flow is a black list entry, the flow MUST be terminated immediately. If any of the remaining flows do not match an entry in the white list, they also MUST be terminated immediately. White listed flows MUST be allowed to continue.

The NAS provisions named multicast service profiles containing grey lists on the AN using the Provisioning message containing one or more Multicast-Service-Profile TLVs. The NAS MAY update the contents of these profiles from time to time as required, by sending additional Provisioning messages with Multicast-Service-Profile TLVs containing incremental modifications to the existing grey lists or replacements for them. The NAS assigns a specific multicast service profile to an individual access line using the Port Management message containing a Multicast-Service-Profile-Name TLV. The NAS MAY change profiles on the line by sending a subsequent Port Management message identifying a new profile. The NAS MAY perform admission control for grey-listed flows. In that case, the NAS MUST NOT include the MRepCtl-CAC TLV in a Provisioning message sent to the AN. Alternatively, the NAS MAY enable admission control at the AN for grey-listed flows. To do this, it MUST include the MRepCtl-CAC TLV in a Provisioning message sent to the AN and MUST also provide a Bandwidth-Allocation TLV in a Port Management message for each access line.

The conditional access with grey lists capability assumes that IGMP/MLD requests are terminated on the AN. When the AN receives a "join" request, it MUST determine whether there is a match to the requested flow in the grey list of the multicast service profile provisioned against the given access line. If there is no match, the request is discarded. Otherwise, the AN MUST send a Multicast Admission Control message to the NAS with content identifying the access line and the multicast flow to be added. As indicated in , the AN MAY add information identifying the requestor by IP address and/or MAC address. If the NAS decides to enable the flow, it MUST send a Multicast Replication Control request to the AN to replicate the flow to the access line with the Result field set to Nack (0x1), as described in . When the AN receives the Multicast Replication Control request, it performs admission control if admission control has been enabled as described in the previous section. If admitting the flow would cause the committed multicast bandwidth at the access line to exceed the provisioned limit, the AN reports an error to the NAS as described in . Otherwise it replicates the multicast flow as requested. If the NAS decides not to permit the flow, it MAY send a Multicast Replication Control message in response to the Multicast Admission Control message to allow the AN to update its internal records. The content of this message is described in . When the AN receives a "leave" request, it MUST terminate replication of the flow to the access line. It MUST then send a Multicast Admission Control message to the NAS indicating the deletion. The NAS updates its internal records but MUST NOT respond to the message. If the AN receives a Provisioning message which updates an existing multicast service profile, the AN MUST review the status of active flows on all ports to which the updated profile has been assigned. Similarly, if a Port Management message that assigns a new profile to a given port, the AN MUST review all active flows on that port. In either case, if any flow does not match an entry in the grey list, it MUST be terminated immediately.

The NAS SHOULD provision an initial amount of delegated multicast bandwidth for each access line using the Port Management message containing the Bandwidth-Allocation TLV. If it fails to do so and a value has not been provisioned on the AN by other means, the AN will be forced to request a bandwidth allocation as soon as it receives a "join" request. The NAS MAY at any time force an update of the amount of delegated bandwidth by the same means.

The delegated bandwidth capability assumes that IGMP/MLD requests are terminated on the AN. When the AN receives a "join" request, it checks whether it has sufficient remaining uncommitted multicast bandwidth on the access line to accommodate the new multicast flow. If not, it MAY send a request to the NAS for an increased allocation of delegated bandwidth, using the Bandwidth Reallocation Request message. The NAS MUST return a Bandwidth Transfer message indicating whether it has granted the request, and if so, what is the new amount of delegated bandwidth. If the AN has sufficient uncommitted multicast capacity to admit the request, either originally or as the result of a successful request to the NAS, it replicates the requested flow to the access line. Otherwise it discards the request. When the AN receives a "leave" request for an active flow, it ceases replication. The NAS or AN MAY at some point detect that their respective views of the amount of delegated bandwidth are inconsistent. If so, they can recover using procedures described in and . As a further aid to synchronization, either the NAS or the AN MAY from time to time check the peer's view of the amount of delegated bandwidth using the Delegated Bandwidth Query message. The NAS or AN MAY at any time release bandwidth to the peer using an autonomous Bandwidth Transfer message. The contents of this message are described in .

If conditional access with white and black lists is combined with conditional access with grey lists, provisioning of the multicast service profiles is as described in except that multicast service profiles will also include grey lists. Admission control is enabled independently on the AN for white lists by including the White-List-CAC TLV in the Provisioning message and for grey lists by including the MRepCtl-CAC TLV in the Provisioning message. The Bandwidth-Allocation TLV provisions an amount that applies to both white- and grey- listed flows if admission control is enabled for both. With regard to multicast service procedures, one point of difference from the individual capabilities must be noted. This is an interaction during the profile matching procedure. The AN MUST seek the best match amongst multiple lists as described in . However, if there are multiple matches of equal precision, the order of priority is black list first, grey list second, and white list last. Once profile matching has been completed, processing of a "join" request is as described in for white or black listed flows or for grey listed flows. Requests that do not match any list SHOULD be discarded. When the AN receives a "leave" request, it MUST terminate replication of the flow to the access line. If the flow was grey-listed, the AN MUST then send a Multicast Admission Control message to the NAS indicating the deletion. Thus the AN needs to retain the fact that the flow was grey-listed for the life of the flow. If the AN receives a Provisioning message which updates an existing multicast service profile, the AN MUST review the status of active flows on all ports to which the updated profile is currently assigned. Similarly, if a Port Management message assigns a new multicast service profile to a given port, the AN MUST review all active flows on that port. If any flow has its most specific match in a black list entry, it MUST be terminated immediately. If any of the remaining flows do not match an entry in the white or grey list, they MUST also be terminated immediately. Finally, if any remaining flows were originally admitted because they were white-listed, but after the change they are grey-listed, the AN MUST generate a Multicast Flow Query response message autonomously as if it were responding to a Multicast Flow Query request, listing all such flows. These flows MUST be allowed to continue until the NAS or the subscriber terminates them. Flows with their most specific match in the white list MUST be allowed to continue. The autonomously-generated Multicast Flow Query response message MUST be formatted as if it were a successful response to a request containing no Target and no Multicast-Flow TLV, as described in , with the exception that the Transaction-Id MUST be set to all zeroes.

The provisioning and bandwidth management procedures of apply in addition to the procedures in , , or as applicable. Admission control follows the rules for conditional access in terms of matching flows against white and black and/or grey lists and performing or not performing bandwidth checks at the AN, but the amount of bandwidth used by the AN to perform admission control is negotiable as described in .

NAS-initiated replication can coexist with the other capabilities, but some means must exist to prevent double replication of flows. The simplest way to do this is to terminate all IGMP/MLD requests on the AN, so that NAS-initiated replication is stimulated only by signalling through other channels. Other arrangements are possible, but need not be discussed here. Assuming the necessary separation of responsibilities, the only point of interaction between NAS-initiated replication and the other multicast capabilities is in the area of admission control. Specifically, if the AN is to do admission control for flows added by Multicast Replication Control messages, regardless of whether they are part of NAS-initiated replication or grey list multicast service processing, the NAS includes the MRepCtl-CAC TLV in a Provisioning message and the Bandwidth-Allocation TLV in a Port Management message. If instead the NAS will do admission control for flows added by Multicast Replication Control messages, regardless of whether they are part of NAS-initiated replication or grey list multicast service processing, it does not send the MRepCtl-CAC TLV in a Provisioning messages to the AN. The NAS can independently enable Admission Control for white flows on the AN by including the White-List-CAC TLV in the Provisioning message.

Committed bandwidth reporting can take place independently of which other multicast capabilities have been negotiated. However, some combinations do not make sense because of redundancy. In particular, the NAS obtains the same information that committed bandwidth reporting gives if the only other capabilities operating are NAS-initiated replication and/or conditional access with grey lists.

The security considerations of ANCP are discussed in and in . Multicast does not in principle introduce any new security considerations, although it does increase the attractiveness of the ANCP protocol as a means of denial of service (e.g., through direction of multicast streams onto the target) or theft of service.

IANA NOTE: Please replace XXXX with the RFC number of this document. This document defines the following additional values within the ANCP Message Type Name Space registry: Message Type Message Name Reference 144 Multicast Replication Control RFC XXXX 145 Multicast Admission Control RFC XXXX 146 Bandwidth Reallocation Request RFC XXXX 147 Bandwidth Transfer RFC XXXX 148 Delegated Bandwidth Query RFC XXXX 149 Multicast Flow Query RFC XXXX 150 Committed Bandwidth Report RFC XXXX This document defines the following additional values for the ANCP Result Code registry: Result Code One-Line Description Reference 0x64 Command error. RFC XXXX 0x65 Invalid flow address. RFC XXXX 0x66 Multicast flow does not exist. RFC XXXX 0x67 Invalid preferred bandwidth amount. RFC XXXX 0x68 Inconsistent views of delegated bandwidth amount. RFC XXXX 0x69 Bandwidth request conflict. RFC XXXX This document defines the following additional values for the ANCP Command Code registry: Command Code Value Command Code Directive Name Reference 1 Add RFC XXXX 2 Delete RFC XXXX 3 Delete All RFC XXXX 4 Admission Control Reject RFC XXXX 5 Conditional Access Reject RFC XXXX 6 Admission Control and Conditional Access Reject RFC XXXX This document defines the following additional values within the ANCP TLV Type Registry: Type Code TLV Name Reference 0x0013 Multicast-Service-Profile RFC XXXX 0x0015 Bandwidth-Allocation RFC XXXX 0x0016 Bandwidth-Request RFC XXXX 0x0018 Multicast-Service-Profile-Name RFC XXXX 0x0019 Multicast-Flow RFC XXXX 0x0021 List-Action RFC XXXX 0x0022 Sequence-Number RFC XXXX 0x0024 White-List-CAC RFC XXXX 0x0025 MRepCtl-CAC RFC XXXX 0x0092 Request-Source-IP RFC XXXX 0x0093 Request-Source-MAC RFC XXXX 0x0094 Report-Buffering-Time RFC XXXX 0x0095 Committed-Bandwidth RFC XXXX This document defines the following additional values for the ANCP Capability Type registry: Value Capability Type Name Tech Type Capability Data? Reference 3 NAS-Initiated Replication 0 No RFC XXXX 5 Committed Bandwidth Reporting 0 No RFC XXXX 6 Conditional Access With White and Black Lists 0 No RFC XXXX 7 Conditional Access With Grey Lists 0 No RFC XXXX 8 Bandwidth Delegation 0 No RFC XXXX

The authors would like to acknowledge Wojciech Dec for providing useful input to this document, Robert Rennison for his help in shaping the definition of the Multicast-Service-Profile TLV, Shridhar Rao for his comments and suggestions and Aniruddha A for his proposal that formed the base of the Multicast Flow Reporting solution. Philippe Champagne, Sanjay Wadhwa and Stefaan De Cnodder provided substantial contributions on the solution for the NAS initiated multicast control use case. Kristian Poscic provided the committed bandwidth reporting use case.

&rfc2119; &rfc6320; IEEE IEEE &rfc5713; &rfc5384; IANA

This appendix provides an example in which most of the possible message flows for multicast control are illustrated. This appendix is for informational purposes only. In case of discrepancy with text of the body of this document, the text in the body of the document is to be considered as the normative text. Assume the following, for a given access port: The basic subscribed service is white-listed. The AN will be responsible for admission control for this service. Some premium services are available, but requests for these services must be referred to the policy server for proper credit processing. For this reason they are grey-listed. The NAS will be responsible for admission control for these services. The subscriber has asked that certain services be blocked so that his children cannot view them. These services are black-listed. All of the above services are Source-Specific Multicast (SSM). In addition, by means which bypass the AN, the subscriber can signal intent to join an on-line game service which is Any Source Multicast (ASM). The NAS is responsible for admission control for this service. Bandwidth delegation is in effect to share video bandwidth between the AN and the NAS. The stated conditions require the use of four of the five capabilities specified in this memo.

Assume that capability negotiation has been completed between the AN and NAS and that the set of negotiated capabilities includes the following four multicast capabilities: NAS-initiated replication, conditional access with white and black list, conditional access with grey list, and bandwidth delegation. At this point, the NAS can provision the service profiles on the AN and enable admission control at the AN for white-listed flows. To do this, the NAS sends the AN a Provisioning message containing this information. An example message providing the profile for our assumed subscriber is shown in . The message has the following contents: Message type is 93. The Result and Result Code fields in the header are set to zeroes, as specified . A Transaction identifier is assigned by the NAS. The Multicast-Service-Profile TLV (of which typically there would be multiple instances) contains a Multicast-Service-Profile-Name TLV (with a length of 20 octets assumed for the example) and three List-Action TLVs, one each for the white, grey, and black lists within the profile. The white list flows come in two sets of group addresses: 233.252.0.0/29, coming from a server at 192.0.2.15, and 233.252.0.32/29, coming from a server at 192.0.2.16. The grey-listed flows are in the band 233.252.0.64/29, coming from a server at 192.0.2.21. Finally, the black list flows are two individual flows that happen to overlap with the grey list band: 233.252.0.65, and 233.252.0.69, also with source 192.0.2.21. The White-List-CAC TLV indicates that the AN does admission control on white-listed flows.

1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type (0x880C) | Length = 132 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Version | Msg Type = 93 | 0x00 | Result Code = 0x000 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Partition ID | Transaction Identifier | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |I| SubMessage Number | Length = 132 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | M-Serv-Prof TLV Type = 0x13 | TLV Length = 112 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | M-S-Prof-Name TLV Type = 0x18 | Embedded TLV Length = 20 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Multicast service profile name | ~ = "Cust 0127-53681-0003" ~ | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | List-Action TLV Type = 0x21 | Embedded TLV Length = 28 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Oper = 0x01 |Lst Typ = 0x01 | Reserved = 0x0000 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Address Family = 0x01 | List Length = 20 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | G Preflen = 29| S Preflen = 32| Group prefix = | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 233.252.0.0 | Source prefix = | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 192.0.2.15 | G Preflen = 29| S Preflen = 32| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Group prefix = 233.252.0.32 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Source prefix = 192.0.2.15 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | List-Action TLV Type = 0x21 | Embedded TLV Length = 18 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Oper = 0x01 |Lst Typ = 0x03 | Reserved = 0x0000 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Address Family = 0x01 | List Length = 10 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | G Preflen = 29| S Preflen = 32| Group prefix = / +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ / 233.252.0.64 | Source prefix = / +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ / 192.0.2.21 | Padding = 0x0000 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | List-Action TLV Type = 0x21 | Embedded TLV Length = 28 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Oper = 0x01 |Lst Typ = 0x02 | Reserved = 0x0000 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Address Family = 0x01 | List Length = 20 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | G Preflen = 32| S Preflen = 32| Group prefix = / +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ / 233.252.0.65 | Source prefix = / +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ / 192.0.2.21 | G Preflen = 32| S Preflen = 32| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Group prefix = 233.252.0.69 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Source prefix = 192.0.2.21 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |White-List-CAC TLV Type = 0x24 | TLV Length = 0 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

TLV lengths in the figure are given in decimal for easier understanding. Note that the padding after the middle List-Action TLV is counted as part of length of the Multicast-Service-Profile TLV, but is not included in the length of that List-Action TLV. Note also that the Length field in the message header, unlike those in the TLVs, includes the message header itself, as required by . Finally, note that the Provisioning message does not include a MRepCtl-CAC TLV since in our example admission control for grey listed flows and for NAS-initiated replication is performed by the NAS. As soon as the AN port comes up, the AN sends an ANCP PORT_UP message to the NAS specifying the Access Loop Circuit ID. The NAS replies with an ANCP Port Management message that, together with the other parameters, includes the multicast service profile name to be associated to that port along with the initial amount of delegated bandwidth. The corresponding message flow is illustrated in .

| | | | |(M1)PORT_UP(Port ID) | | | |-------------------->| | | | (*) | | |(M2) PORT_MNGT | | | | (Port ID, | | | |Mcast S Profile Name,| | | |Bandwidth Allocation)| | | |<--------------------| (*) The NAS may optionally seek direction from an external Autorization/Policy Server ]]>

The Port Management message will typically contain other TLVs but our example () just shows the Target, Multicast-Service-Profile-Name, and Bandwidth-Allocation TLVs. The Target TLV identifies the subscriber line, the Multicast-Service-Profile-Name TLV is identical to the one contained in the Provisioning message, and the Bandwidth-Allocation TLV provides just enough bandwidth (2000 kbits/s) for one channel to start with. The following fields in the Port Management message header are shown with specific values either as directed by the base protocol document or for the sake of our example: Message Type is 32. Result is set to Nack (0x01) for this example. Result Code is 0x000. Port is set to 0. Event Sequence Number, the R flag and the other bits marked x, Duration, the Event Flags, and the Flow Control Flags are all irrelevant for this function and are set to 0. Function is set to 0x8, "Configure Connection Service Data". X-Function is set to 0. Tech Type is 0x05 (DSL). Block lengths are calculated assuming a Circuit-Id length of 4 in our example. Recall that the example Multicast-Service-Profile-Name TLV length is 20.

1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type (0x880C) | Length = 84 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Version | Msg Type = 32 | 0x01 | Result Code = 0x000 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Partition ID | Transaction Identifier | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |I| SubMessage Number | Length = 84 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Port = 0 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Port Session Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Event Sequence Number = 0 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |R|x|x|x|x|x|x|x| Duration = 0 | Function = 0x8| X-Function = 0| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Event Flags | Flow Control Flags | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |x|x|x|x|x|x|x|x| Msg Type = 32 |Tech Type=0x05 | Blk Len = 56 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | # of TLVs = 3 | Extension Block length = 44 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Target TLV Type = 0x1000 | Target TLV Length = 8 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Access-Loop-Circuit-ID 0x0001 | Circuit-ID Length = 4 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Access Loop Circuit ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | M-S-Prof-Name TLV Type = 0x18 | TLV Length = 20 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Multicast service profile name | ~ = "Cust 0127-53681-0003" ~ | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | BW Alloc TLV Type = 0x15 | TLV Length = 4 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Bandwidth value = 0x000007D0 (2000 kbits/s) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Suppose now that the subscriber chooses to watch the premium channel characterized by source 192.0.2.21, group 233.252.0.67. Upon receiving the Join request, the AN matches it against the multicast service profile for the port and determines that it is a grey-listed flow. illustrates the resulting ANCP message flow for the case of a simple join and leave, when admission control for grey-listed flows is not activated on the AN. To start the flow, the AN sends a Multicast Admission Control request (M1) to the NAS. The NAS decides whether flow can be admitted, applying both policy and bandwidth criteria. It returns its decision (positive in this example) in a Multicast Replication Control message (M2). Later, when the subscriber leaves the flow, the AN informs the NAS by sending another Multicast Admission Control message.

| NAS | +----------+ |Gateway| +-----+ +-----+ | +-------+ | | | | | Multicast | | Join(Grey-Fl) | Admission | |-----------+---------->| Control (M1) | | | |------------------>| | | | | (NAS performs | | | Multicast | admission | | | Replication (*) control) | | | Control (M2) | | Mcast Grey Flow |<------------------| |<======================+ | | | | | ~ ~ ~ ~ | | | Multicast | | Leave(Grey-Fl) | Admission | |-----------+---------->| Control (M3) | | | |------------------>| | | | | Grey-Fl : Multicast Flow matching an entry in grey List ]]> (*) The NAS may optionally seek direction from an external Authorization/Policy Server

The Multicast Admission Control message M1 contains: an ANCP Header with: Message-Type = 145 - Multicast Admission Control; Result= 0x0 (Ignore); Transaction-ID = Transaction-ID maintained by AN; a Target TLV identifying the AN Port a Command TLV containing: Command Code = Add (1); Accounting = 0; a Multicast-Flow embedded TLV indicating the SSM multicast flow (Flow Type = 0x02) for which the AN received the IGMP Join: IPv4 (0x01) Group address= 233.252.0.67, IPv4 (0x01) Source Address = 192.0.2.21; a Request-Source-IP embedded TLV containing the IGMP join source IP (192.0.2.100). The Multicast Admission Control message M1 is illustrated in :

The Multicast Replication Control message M2 contains: an ANCP Header with: Message Type = 144 - Multicast Replication Control; Result= 0x1 (NAck); Transaction-ID = Transaction-ID maintained by NAS; a Target TLV identifying the AN Port; a Command TLV containing: Command Code = Add (1); Accounting = 1 (begin flow accounting), since in our example the operator wants accounting on this flow. a Multicast-Flow embedded TLV indicating the SSM multicast flow (Flow Type = 0x02) that the NAS is admitting for this access port: IPv4 (0x01) Group address= 233.252.0.67, IPv4 (0x01) Source Address = 192.0.2.21. The Multicast Admission Control message M2 is illustrated in .

The Multicast Admission Control message M3 advising the NAS that the flow has been terminated contains: an ANCP Header with: Message-Type = 145 - Multicast Admission Control Result= 0x0 (Ignore) Transaction-ID = Transaction-ID maintained by AN a Target TLV identifying the AN Port a Command TLV containing: a Command Code = Delete (2); Accounting = 0; a Multicast-Flow embedded TLV indicating the SSM multicast flow (Flow Type = 0x02) for which the AN received the IGMP leave: IPv4 (0x01) Group address= 233.252.0.67, IPv4 (0x01) Source Address = 192.0.2.21. a Request-Source-IP embedded TLV containing the IGMP leave request source, IPv4 (0x01) address 192.0.2.100. The Multicast Admission Control message M3 is illustrated in .

The NAS has enabled white list admission control on the AN, and the bandwidth delegation capability has been negotiated. White listed flows in themselves require no messages to the NAS, either upon admission or upon termination, but the AN may request an increase in the amount of delegated bandwidth if it needs the increase to admit a flow. Consider an example where the AN has already admitted one white-listed flow, thereby using up the initially provisioned amount of delegated bandwidth (2000 kbits/s). A request is received to join a new flow in the white list range. The AN chooses to send a Bandwidth Reallocation Request message to the NAS, requesting that the delegated bandwidth allocation be increased to 4000 kbits/s at a minimum, and preferably to 6000 kbits/s. In our example, the NAS is managing bandwidth tightly, as witnessed by its minimal initial allocation of just enough for one flow. It is willing to provide the minimum additional amount only, and therefore returns a Bandwidth Transfer message where the delegated bandwidth value is given as 4000 kbits/s. With this amount, the AN is able to admit the second white-listed flow. The AN could send a similar Bandwidth Transfer message back to the NAS bringing the delegated bandwidth amount back down to 2000 kbits/s when one of the flows is terminated, but this shows nothing new and is omitted. As one more point of illustration, suppose that the NAS chooses to audit the current amount of delegated bandwidth to ensure it is synchronized with the AN. It sends a Delegated Bandwidth Query request message to the AN, and receives a Delegated Bandwidth Query response message with the current allocation as the AN sees it. The complete message flow is shown in .

| NAS | +----------+ |Gateway| +-----+ +-----+ | +-------+ | | | | | | | Join(White-F1) | | |-----------+---------->| | | | |AN performs | | Mcast White Flow 1 | admission control | |<======================+ | | | | | | Join(White-F2) | | |-----------+---------->|No bandwidth left | | | | | | | |Bandwidth | | | | Reallocation Req | | | |------------------>|(M1) | | | | | | | (*) | | |Bandwidth Transfer | | AN can now |<------------------|(M2) | admit flow | | | Mcast White Flow 2 | | |<======================+ | | | | | ~ ~ ~ ~ | | |Delegated Bandwidth| | | | Query request | | | |<------------------|(M3) | | | | | | |Delegated Bandwidth| | | | Query response | | | |------------------>|(M4) | | | | ]]> (*) The NAS may optionally seek direction from an external Authorization/Policy Server

The Bandwidth Reallocation Request message (M1) is shown in . The contents require little explanation. The Message Type for the Bandwidth Reallocation Request is 146. The Result field is set to 0x0 (Ignore). Besides the Target, the message has one other TLV, the Bandwidth-Request, with a TLV Type of 0x16. The TLV contains Required Amount and Preferred Amount fields, set to 4000 and 6000 kbits/s respectively.

The Bandwidth Transfer message (M2) is shown in . Again, the contents are easily understood. The Message Type for the Bandwidth Transfer message is 147. The Result field is set to Success (0x3). The message contains the Target TLV and the Bandwidth-Allocation TLV. The latter has a TLV Type of 0x15 and contains a Delegated Amount field, set to 4000 kbits/s.

The Delegated Bandwidth Query request message (M3) is shown in . The Message Type for the Delegated Bandwidth Query request message is 148. The Result field is set to AckAll (0x2). The message contains the Target TLV only.

Finally, the Delegated Bandwidth Query response message (M4) is shown in . The Message Type for the Delegated Bandwidth Query response message is 148. The Result field is set to Success (0x3). The message contains the Target TLV and the Bandwidth-Allocation TLV with the Delegated Amount field set to 4000 kbits/s.

This section introduces no new messages, since requests for flows in the black list are simply ignored. The one thing to point out is the overlap in our example between the set of flows in the grey list and the flows in the black list. This does not create any ambiguity, since not only does the black list have priority for equally good matches, but also the black list entries are more specific (group prefix lengths of 32 versus 29 in the grey list) than the grey list flow prefixes.

The final class of multicast control actions in our example allows the subscriber to enter and leave the on-line game. As described at the beginning of this example, the game uses Any Source Multicast (ASM). Subscriber signalling bypasses the AN, going directly to the NAS (e.g., through a web interface). When the subscriber requests to join the game, the NAS (after applying policy and bandwidth checks) sends a Multicast Replication Control message to the AN to enable the flow on the port concerned. The AN knows not to apply admission control, since it has not received an MRepCtl-CAC TLV in the Provisioning message. When the subscriber leaves, the NAS sends another Multicast Replication Control message to delete the flow. This message sequence is shown in . It is possible that the NAS finds that there is not enough bandwidth available to accommodate the subscriber's request. In this case, the NAS could send a Bandwidth Reallocation Request message to the AN, asking it to release some of the bandwidth delegated to it. This is not shown in the present example, since the messages are the same as those already presented with the exception that the Preferred Amount in the request will be *less than* or equal to the Required amount, rather than *greater than* or equal to it.

| NAS | +----------+ |Gateway| +-----+ +-----+ | +-------+ | | | | | | | Join game | | |-----------+------------------------------>| | | | Multicast | NAS performs | | | Replication (*) admission | | | Control (M1) | control | Mcast Game Flow |<------------------| |<=====================>+ | | | | | ~ ~ ~ ~ | | | | | Leave game | | |-----------+------------------------------>| | | | Multicast | | | | Replication | | | | Control (M2) | | Mcast Game Flow |<------------------| | discontinued | | | | | | ]]> (*) The NAS may optionally seek direction from an external Authorization/Policy Server

Multicast Replication Control message (M1) in looks like the message in with two exceptions. The first is that the NAS has the option to set the Result field to AckAll (0x02) if it needs positive reassurance that the flow has been enabled. This was not done here to save having to depict a response differing only in the Result field. The larger difference in this example is that the flow description in the Multicast-Flow embedded TLV is that of an ASM multicast group (Flow Type = 0x01) with IPv4 (0x01) group address 233.252.1.100.

Message M2 terminating the flow when the subscriber leaves the game looks the same as the message in with two exceptions: the Command Code becomes Delete (2), and Accounting is set to 0 to turn off flow accounting. Of course, the Transaction Identifier values will differ between the two messages.

The example in this section is independent of the example in the preceding sections. illustrates a message flow in a case where the NAS queries the AN about which multicast flows are active on port 10, on port 11 and on port 20 of the AN.

| NAS | +----------+ |Gateway| +-----+ +-----+ | +-------+ | | | | | Multicast Flow | | | | Query Request | | | | (M1) | | | |<------------------| | | | | | | | Multicast Flow | | | | Query Response | | | | (M2) | | | |------------------>| | | | | | | | | ]]>

The Multicast Flow Query Request message (M1) is illustrated in . The Message Type is 149. The Result field is set to AckAll (0x2). Three Target TLVs are present, identifying port 10, port 20, and port 11 respectively.

The Multicast Flow Query Response message (M2) is illustrated in . It indicates that there is one active multicast flow [(192.0.2.1, 233.252.2.4)] on port 10, no active multicast flow on port 20 and two active multicast flows [(192.0.2.1, 233.252.2.4) and (192.0.2.2, 233.252.2.10)] on port 11.